Log in to HSS DIY today to track your deliveries, extend your hire and check out faster, all in one place.

Log in to HSS DIY today to track your deliveries, extend your hire and check out faster, all in one place.

Log in to HSS DIY today to track your deliveries, extend your hire and check out faster, all in one place.

Log in to HSS DIY today to track your deliveries, extend your hire and check out faster, all in one place.

Log in to HSS DIY today to track your deliveries, extend your hire and check out faster, all in one place.

HSS DIY home

Browse

How to add garden lighting for autumn and winter evenings

Written by: 

Date: 

Categories: Electrical & Lighting, Outdoor Lighting, How to Guides - Electrical & Lighting, Garden & Outdoor, DIY, , Autumn

Warm festoon lights and pathway spike lights in a garden

⏱ Read time: 8 min | 🌿 Difficulty: Beginner | ⏰ Time: Half a day (4 hrs) | 👷 1 person

The clocks go back at the end of October and the garden will be pitch black by half four. Most of us write off any garden time until March, but we’re here to tell you, you don’t have to. A handful of well placed outdoor garden lights turns your dark garden back into somewhere you actually walk, sit and use, no matter the season.

Here is how to do it properly with HSS DIY.

Why is autumn the right time to add outdoor lighting?

By mid December the sun sets before 4pm across most of the UK, so autumn is the perfect time to add outdoor lighting before the darker nights arrive.

You’ll be able to see where needs lighting instead of guessing and putting them in the wrong place. Plants will have started to die back which means thinner borders and no new growth on shrubs that can be destroyed.

Soil is also soft enough to dig in October, making it easier to work with.

There is a safety angle too -

  • you’ll be able to see wet leaves on a dark path, which will of course be slippy
  • it’ll be bright when you need to drag your bins out at 6pm
  • you won’t miss a forgotten step and potentially trip or fall
Warm white garden pathway lights glowing on an autumn evening with fallen leaves

Already know what you want and just need fixture ideas? Our guide to outdoor lighting covers different lighting types and styles you might want for your garden.

What can I fit myself, and what needs an electrician?

There are some parts of installing outdoor lights that you can do yourself, however, some will need a registered electrician.

Here’s what lighting types can be fitted by you or an electrician.

Lighting type
Who can fit it
Best for
Solar spike and wall lights
You, no wiring
Borders, fence posts, quick wins
Plug in 12V or 24V kit
You, from an existing outdoor socket
Paths, steps, planting beds
Rechargeable or plug in festoon lights
You, plug and hang only
Patios, pergolas, seating areas
New outdoor socket or spur
Registered electrician
Anything permanent
Mains armoured cable run to a shed
Registered electrician
Floodlights, garden offices, water features

What kit do I need?

The list of kit you’ll need for adding and installing lights for autumn is long, but they are all needed.

Here’s what you need.

Kit
What it does
Get it from HSS DIY
Lights and controls
Fixtures, timers and sensors
Electrical and lighting or security lighting
RCD adaptor
Cuts the power if a cable gets nicked
Buy an RCD adaptor or hire an RCD breaker
Cable reel or lead
Gets power safely down the garden
Buy a 25m cable reel or hire a lead
Cable and pipe detector
Finds what is already buried
3 in 1 detector or CAT 4 locator
Turf cutter or micro digger
Lifts turf neatly, digs long runs fast
Turf cutter hire or micro digger hire
Conduit and duct rod
Protects cable, pulls it through
Oval conduit, clips, duct rod hire
Work light
Lets you see what you are doing
Rechargeable work light hire
PPE
Gloves, knee pads and eye protection
Knee pads, goggles, PPE

How do I add outdoor lighting, step by step?

Step 1: Walk the garden in the dark first

Go out with a torch after sunset and walk the routes you actually use: back door to shed, bins to the gate, patio to the lawn. Note where you hesitate, trip or reach for your phone torch. Those spots are your priority list. Light them first and add the rest later.

Step 2: Split the garden into zones

Three is plenty:

  • Route: paths, steps and the bin run. Low, even light, ideally on a timer.
  • Task: back door, shed, BBQ. Brighter, often on a PIR sensor.
  • Mood: seating and planting. Soft light on its own switch or dimmer.

Put each zone on its own circuit or switch so you’re not lighting the whole garden to put the bins out.

Step 3: Choose warm white, and go dimmer than you think

Every bulb’s box lists its colour temperature, measured in kelvin (K). This tells you how warm or cool the light looks. Lower numbers give a softer, more yellow glow, and higher numbers look bluer and harsher.

For gardens, stick to 2700K–3000K, usually labelled “warm white”. It flatters brick, stone and planting. Cool white (4000K and above) makes a garden look like a car park in British drizzle.

Brightness is a separate figure, measured in lumens. As a guide:

  • Path and step lights: 50–100 lumens each
  • Wall and door lights: 150–200 lumens
  • Uplighters on trees: 100–300 lumens, depending on size

Overlighting is the most common mistake. Start low, because you can always add more. For winter, check that fittings are at least IP65, and IP67 for anything at ground level that will sit in wet soil or leaf litter.

Step 4: Check your power source and protection

Any outdoor socket should be weatherproof (IP66 when in use) and protected by a 30mA RCD. If there’s no outdoor socket, or you’re not sure about the RCD, call an electrician.

New outdoor mains circuits are notifiable under Part P, so use an NICEIC- or NAPIT-registered installer and get the certificate.

A 12V low-voltage kit running from a transformer indoors or in a weatherproof box avoids most of this and is safe to fit yourself.

Step 5: Plan the cable route and scan it

Run cable along edges, walls and border lines rather than across open lawn, so future digging is predictable. Sketch the route and keep it with your house papers. Scan the route with a cable detector before you dig. Older gardens hide water pipes, old supply cables, drains and the odd surprise.

Step 6: Lift the turf and dig the run

A spade is fine for a short run. A turf cutter lifts clean strips you can lay straight back. Roll them up, keep them damp and shaded, and relay within a day or two. For long runs, hire a micro digger or trencher. Autumn helps here: the soil is softer than in summer and not yet frozen or waterlogged.

Step 7: Lay the cable at the right depth

The depth depends on the voltage.

  • Mains (230V): This is a job for your electrician. They’ll use steel wire armoured (SWA) cable and bury it about 450mm deep under beds and paths, or 600mm under lawn and anywhere you might dig later. A strip of warning tape laid about 150mm above the cable will warn anyone who digs there in future.
  • Low-voltage (12V): You can do this yourself with outdoor-rated low-voltage cable. Bury it 150–200mm deep, or clip it along edges and walls. In beds, keep it below spade depth.

Either way, run the cable through ducting so it can be replaced later without digging. Backfill in layers, firming each one down, and then relay the turf. Before you fill the trench, take a photo of it with a tape measure in shot.

Step 8: Fit the lights, aim them, then set the controls

Point beams down at the ground or into the planting, not at windows, the sky or a neighbour’s bedroom. Installing shielded or hooded fittings help with this. Then set up control by zone:

  • Route: astro timer that follows sunset and switches off at a set time, say 11pm
  • Task: PIR sensor, with a short timeout
  • Mood: manual switch, dimmer or smart plug

Test everything on a dark evening and adjust angles if needed. Cutting the light after midnight is kinder to wildlife too.


Person installing low voltage garden spike lights along a path edge with conduit

How deep should the cable go?

Different cable types will need to be installed at different depths in your garden.

Here are some examples.

Cable type
Depth
Also do this
12V or 24V low voltage
50 to 100 mm
Sleeve in conduit. The risk is a spade, not shock
Mains armoured, garden or lawn
Around 500 mm
Warning tape 150 mm below the surface
Mains armoured, under a drive
Around 600 mm
Duct it, clear of vehicle loading points

BS 7671 asks for sufficient depth rather than a number, so the mains figures are the sensible domestic position, not a hard rule. Your electrician will decide this on site.

Which IP rating do I need where?

IP ratings tell you how much water and muck a fitting can shrug off. Get it wrong and you’ll be replacing lights in February. Match the minimum rating to where the light goes:

  • Under a porch or pergola: IP44. It only has to cope with splashes, because it never takes direct rain.
  • On an open wall, fence or post: IP65. It has to stand up to driven rain and being hosed down.
  • Set into a path or border: IP67. It needs to survive puddles and brief immersion.
  • In a pond or water feature: IP68. This is the rating for constant immersion.

If you’re unsure, go one rating higher. The extra cost is small compared with replacing a failed light.

Weatherproof IP65 rated outdoor wall light mounted on a garden wall in wet conditions

How long will it take?

It depends on how many lights you’re fitting and what type they are. As an example, here’s a timeline for one person installing a plug-in low-voltage path and patio scheme with a festoon:

  • Planning after dark (30 mins): Walk the garden, mark the spots and count the fittings.
  • Scanning and setting out (30 mins): Run the detector along the route and mark the turf.
  • Lifting turf and digging (1 hour): Dig a shallow run for the low-voltage cable.
  • Laying cable and fittings (1 hour 15 mins): Put in the ducting, cable and connectors, then backfill and relay the turf.
  • Aiming and setting controls (45 mins): Position each beam, set the timer and test it after dark.

Total: about 4 hours, or half a day. If you also need a mains run to a shed, allow a full extra day, and that part is a job for your electrician.

What health and safety points should I not skip?

  • Electric shock. Wet ground and mains power are a dangerous mix. Make sure everything is protected by an RCD. Electrical Safety First has more guidance.
  • Striking a buried service. Pipes and old cables lurk under every established garden. Scan the route with a detector before you dig.
  • Working in the dark. At this time of year you’ll run out of daylight sooner than you expect. Set up a work light before you need it.
  • Open trenches. A half-dug run is a broken ankle waiting to happen. Cover it while you work, and never leave it open overnight.
  • Ladder work in the wet. Slippery autumn decking and ladder feet don’t mix. Put the ladder on stable ground, have someone hold it, and wear proper footwear and gloves.
  • Wildlife and neighbours. Bats are legally protected, and artificial light disturbs them. Keep light off hedgerows and tree lines. The Bat Conservation Trust has more advice. Angle fittings away from neighbours’ windows too.

A typical job: Turning a dead patio into an evening space before the clocks change

A semi in Sheffield had a patio that saw no use past September, and a 12-metre path to the shed that turned into a torch job once the light went. An existing weatherproof RCD socket by the back door meant no new supply run — this stayed a one-person job.

Eight plug-in 12V spike lights lined the path at 1.5m spacing, cable run through conduit under a shallow trench cut with a hired turf cutter. A festoon strung across the patio pulled it back into use after dark. All warm white lights, all on an astro timer, so the timing takes care of itself as the nights change.

The shed spur is still on the list — that one needs an electrician.

Should I hire or buy lighting equipmeny?

Deciding on what to do regarding hiring & buying can be a bit of a hard decision, so we’ve put everything together to help you figure out what’s best.

Route
What you get
Makes sense when
Buy the lights and controls
Fittings, timers and sensors that stay put
Always. These are not hire items
Hire the groundwork kit
Turf cutter, micro digger, duct rod, work light
Any run longer than a few metres
Buy the consumables
Conduit, clips, warning tape, RCD adaptor
Cheap, reusable, you will want them again
Buy a turf cutter outright
A machine you use once in five years
Almost never for a domestic garden

Your garden lighting checklist

Need help staying on track? We’ve got you. Print out this checklist, take it outside and tick off each job as you go.

Before you start

☐ Garden walked after dark, trouble spots marked

☐ Zones decided: route, task and mood

☐ Lumens and colour chosen, 2700K to 3000K

☐ IP rating checked for each position

☐ Outdoor socket confirmed weatherproof and RCD protected

☐ Electrician booked if new wiring is needed

☐ Hire kit booked, consumables ordered

On the day

☐ Work light set up before daylight goes

☐ Cable route scanned with a detector

☐ Gloves, knee pads and eye protection on

☐ RCD adaptor in line for every power tool

☐ Turf lifted, kept damp and shaded

☐ Cable sleeved in conduit at the right depth

☐ Trench covered if you stop

Finishing up

☐ Every connection sealed and weatherproofed

☐ Beams aimed down, away from windows and hedgerows

☐ Timer or sensor set and tested after dark

☐ Turf relayed, firmed and watered in

Frequently asked questions

Do I need an electrician to add garden lighting?

Not for solar, or a low voltage kit plugged into an existing weatherproof socket. You do for any new socket, spur or mains cable run, which is notifiable in England and Wales.

Do solar lights actually work in a British winter?



Not brilliantly. With only a few hours of weak daylight in December, a solar spike might manage an hour or two of dim light. Treat solar as decoration. For paths, steps and the back door, use low-voltage or mains lights.

What IP rating do outdoor garden lights need?

IP44 under cover, IP65 for anything exposed to rain, IP67 at ground level where water pools, IP68 in a pond. In doubt, go a rating higher.

How deep should garden lighting cable be buried?

Low voltage cable needs only 50 to 100 mm in conduit, since you are guarding against spades rather than shock. Mains armoured cable sits around 500 mm in a lawn, with warning tape.

Warm white or cool white for a garden?

Warm white. 2700K to 3000K flatters planting, brick and timber. Cool white above 4000K makes your patio look like a retail park at closing time.

Will garden lights bother my neighbours or local wildlife?

They can. Aim beams downward, avoid lighting hedgerows and tree lines where bats commute, and put floodlights on a sensor rather than on all night. See the Bat Conservation Trust guidance on artificial lighting.

The bottom line on lighting your garden for the dark months

And just like that, the job’s done!

Don’t let the dark autumn/winter nights stop you from being in the garden.

Remember: Light the route first, keep it warm, keep it dim, match the IP rating to the spot, and be honest about what needs an electrician. Do that this month and you get five months of a garden you can walk through, not one you squint at through a wet window.

At HSS DIY, you can browse the lighting hire range, add your fittings and PPE, and take next day delivery. Order online 24/7, and grab a project bundle if it suits.

More ideas sit in our outdoor lighting blog and the DIY projects hub, if you need some inspo.

Buy the materials. Hire the tools. One order. All in one place.

Get DIY Happy with HSS DIY: The Home of Great Projects.

Meet the people behind our Tips & Advice

From quick fixes to bigger DIY projects, get to know the people behind the guides helping you get the job done with confidence.

→ Discover our authors


Related Products

Site information

  • Ecovadis Gold 2023 Accreditation
  • Ecovadis Platinum 2025 Accreditation
  • Advanced CHAS Accreditation
  • Hire Association Europe Accreditation

HSS ProService Ltd 2026. All rights reserved.

Company No. 11084154

Building 2, Think Park, Mosley Road, Trafford Park, Manchester, M17 1FQ

As a supplier of partially or fully rebated fuels HSS ProService is approved by HMRC as a registered dealer in controlled oil.